Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

12701 / 3010 Polyether Defoamer for Fermentation

A polyether built specifically for foam control in biological fermentation. It is non-toxic, leaves no spots, and it does not disturb the culture strains in the fermenter.

Models: 127013010Form: PolyetherType: Polyether

Overview

A polyether developed specifically to clear foam out of biological fermentation. It is non-toxic and leaves no spots, picks up little moisture and holds its chemistry in use, and it does not disturb the culture requirements. That covers most processes where silicone defoamers are ruled out.

Key advantages

Built for fermentation duties
Non-toxic in use
Leaves no spots
Low moisture pickup
Does not disturb the culture

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property127013010
Active content≥99.0≥99.0
pH5.0-7.05.0-7.0
Ionic typeNon-ionicNon-ionic

Recommended applications

What decides the model

Cloud point and temperature tolerance decide the choice: a polyether is only useful inside the temperature window where it stays compatible with the liquor. Active content then sets the dose, and ionic type sets whether it will sit quietly next to the surfactants already in the tank.

The models in this family differ in the properties tabulated above; those columns, rather than a product name, are what a shortlist has to be built on.

How to trial these models

Polyether grades are chosen for temperature and for systems where a silicone would be incompatible. Trial at the temperature the process actually runs at, not at room temperature: a polyether that looks slow on the bench often performs once the liquor is hot, and the reverse happens as well. Keep the dose low and step it, because polyether over-dosing tends to show up as cloudiness or as foam that collapses and then rebuilds thicker.

Questions buyers ask about 12701

What is the difference between the 12701 / 3010 models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 12701 do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a polyether defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 12701?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 12701 shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

1000 kg IBC tote of 12701 / 3010 polyether defoamer for fermentation staged for dispatch

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Polyether Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.