Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

F-37 / F391 High-Efficiency Oilfield Defoamer

A modified silicone polyether for crude production, transport, refining and delayed coking. Low silicone content, a high flash point and a low working dose.

Models: F-37F391Form: Water-soluble modified silicone polyetherType: Oilfield

Overview

These grades are organic compounds made by grafting allyl ethers of different HLB value onto low-hydrogen silicone together with high-cloud-point polyoxyethylene ether and polysiloxane, then compounding them by a special process. The product is a water-soluble liquid that kills the bubbles crude extraction, transport, refining and delayed coking produce. Low dose, high efficiency, lasting inhibition — particularly in gas fields run on natural gas, on offshore platforms, and in refining and vacuum residue delayed coking. Silicone content is low, so the foam control stays tight while the safety profile stays reliable. They foam little themselves, emulsify strongly, take both high and low temperature, and hold an intrinsic ability to control foam.

Key advantages

Kills foam fast in extraction and refining
Low-foaming, strong emulsifying power
Tolerates high and low temperature
Holds an intrinsic foam-control ability
Low silicone content, safe to handle
Flash point above 80 °C

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

PropertyF-37F391
AppearanceColourless to pale yellow oily liquid, slight alcoholic odourColourless to pale yellow oily liquid, slight alcoholic odour
Active content≥95.0≥90.0
Viscosity (25 °C, mPa·s)100-1000100-1000
pH5.0-7.55.0-7.5
Density (g/cm³)0.95-1.050.95-1.05
Flash point (°C)>80>80

Recommended applications

  • Crude oil extraction
  • Oil-water separation in gas fields
  • Offshore platform production
  • Refining
  • Vacuum residue delayed coking

What decides the model

Flash point and compatibility with the produced fluid decide the choice here, not the defoaming speed. A grade that defoams brilliantly but flashes low, or that emulsifies with the crude, cannot be used on a separator train.

Across the 2 models in this family the published active content runs from ≥90.0 to ≥95.0. The table above is the only figure we publish, and it is typical rather than a specification.

How to trial these models

Oilfield grades are specified for high flash point and for compatibility with produced fluids, so the trial has to be run on the actual wellstream or separator fluid rather than on water. Where a demulsifier is already in the system, dose the defoamer after it: the two chemistries compete for the same interface, and dosing order is often the difference between a clean separation and a rag layer.

Questions buyers ask about F-37

What is the difference between the F-37 / F391 models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much F-37 do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a oilfield-grade defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of F-37?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a F-37 shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

1000 kg IBC tote of f-37 / f391 high-efficiency oilfield defoamer staged for dispatch

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Oilfield Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.