Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

When the Defoamer Seems to Do Nothing: A Dosing Checklist for Line Technicians

Plenty of defoamer going in and the foam is still there. Before you blame the product, check how it is being dosed.

By the ElonMek technical team · Troubleshooting · Published 2026-10-01

Technician checking dosing equipment on a process line

Plenty of defoamer is going in and the result is still poor. Often the defoamer is not the problem. The way it is dosed is.

When you add it, how you add it, where you inject it and how much: each one decides the final result. Here are the dosing practices that matter, set out for the technicians on the line.

Timing: Two Points That Decide the Outcome

Most operators wait until the foam has built up, then add defoamer in a hurry. It works, but it costs you. The people who know the line add defoamer before the foam exists.

Feed it ahead of the batch, before solution preparation or before startup. It then mixes evenly through the system and lays down a foam-inhibiting layer that holds the foam back at the source. This is preventive dosing, and it beats remedial dosing on both result and consumption.

If heavy foam has already formed, top up close to where the foam is generated. Do not wait for it to spill onto the floor, because accumulated foam is far harder to break. The top-up dose runs 1/3 to 1/2 of the initial dose.

Feeding: Match the Method to the System

  1. Direct dosing, for low-viscosity systems or batch operation. Pour the defoamer in slowly under continuous stirring so it does not settle. Use this route for products marked "do not dilute" in the specification.
  2. Dosing after dilution, for high-viscosity systems or large continuous lines. Dilute the defoamer to a workable ratio with process liquid or deionized water before feeding. It disperses faster and avoids the craters and oil spots that a strong local concentration can leave. Diluted product has to be made up and used at once: emulsion defoamers lose stability once diluted, and left overnight they can separate and stop working.
  3. Continuous metered dripping, for plant that runs round the clock, aeration basins and circulating systems included. A metering pump drips a steady low dose into the foam-generating zone and holds the foam down continuously. That is more stable and longer lasting than an intermittent shock dose, and an automated dosing system will give you better accuracy still.

Injection Point: Feed Where the Foam Starts

The rule is simple. Inject at the source, not onto the foam already sitting on top. Feed near the aerators in an aeration tank, around the impeller in a stirred vessel, or at the pump inlet on a pipeline.

Two details matter. Do not pour onto a still liquid surface. Dose into the turbulent zone or around the stirrer shaft, so the shear spreads the product for you, but not directly above high-speed agitator blades where the shear is too strong.

Dosage: Less Is More

Adding more the moment performance drops is the most common habit on site, and the most dangerous. A bigger dose does not buy a better result: past a certain concentration the performance stops improving. What you get instead is higher cost, floating oil, craters, and now and then the reverse of what you wanted, a dose that stabilizes the foam.

For most cases, start trials at 0.1 ‰ of the total system mass. Reference doses vary widely between industries. Water treatment typically runs 1-50 ppm, while agricultural suspension concentrates may need 1000-5000 ppm. Go by the figure for your own industry.

To fix the number properly, run gradient trials before you commit the line. Take system samples, dose in increments, and find the lowest concentration that still gives you effective foam control. That is your working dose.

On multi-step processes such as coating dispersion and grinding followed by paint mixing, split the dose. Add 50 % at the dispersion stage to hold foam back, and the other 50 % later to break it.

On any foam control job, roughly 70 % of the result comes from product quality and 30 % from how you apply it.

Thirty-five years of defoamer manufacturing sits behind the range: more than 300 grades across silicone-based, polyether-based, mineral-oil-based and higher-alcohol-based chemistry, in use across over 50 industries worldwide.

Keep reading

Related guides

All technical guides

Range

Grades used in this application

All 64 grades

Markets

Buying from Southeast Asia?

The same grade families are supplied to textile, paper and construction plants in Vietnam, Cambodia and Laos.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.