Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

70104B Broad-Spectrum Polyether Fatty-Acid-Ester Defoamer

A broad-spectrum polyether fatty-acid-ester defoamer that breaks or suppresses foam in aqueous systems. It is at its best in water-soluble polymer formulations and medium-to-high viscosity systems.

Models: 70104BForm: Polyether fatty-acid esterType: Mineral Oil / PE Ester

Overview

The 70104B grade is a broad-spectrum polyether fatty-acid-ester defoamer. It clears or suppresses foam in aqueous systems, and it holds up well in two demanding cases: water-soluble polymer formulations and medium-to-high viscosity systems.

Key advantages

Breaks and suppresses foam in aqueous systems
Works well in water-soluble polymer systems
Holds up in medium-to-high viscosity systems

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property70104B
AppearancePale yellow transparent liquid at ambient temperature; a small amount of sediment forms below 5 °C
Active content95.0±1.0
Viscosity (25 °C, mPa·s)100-1500
Ionic typeNon-ionic
Flash point (°C)>165

Recommended applications

What decides the model

Carrier oil, active content and cost per kilo of active matter decide this range. The ester and polyether-ester grades are chosen where a straight mineral oil would affect the finished film or sheet; the mineral-oil grades are chosen where nothing downstream is sensitive to oil.

This family is published as a single model, so there is no internal comparison to make: the table above is the whole of the data we release on it.

How to trial these models

Mineral-oil, ester and polyether-ester grades are the economical route for aqueous systems that do not need silicone performance. They carry a carrier oil, so trial them on the same batch you will run commercially and check for any effect on the downstream film, print or sheet: oil-based grades can change drying or appearance where silicone grades would not. Read the ten-minute foam height and the appearance of the finished product together.

Questions buyers ask about 70104B

What is the difference between the 70104B models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 70104B do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a mineral oil & polyether ester defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 70104B?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 70104B shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

200 kg steel drums of 70104b broad-spectrum polyether fatty-acid-ester defoamer in the filling hall

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Mineral Oil / PE Ester Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.