By the ElonMek technical team · Storage & Handling · Published 2026-10-12

Every summer, stored defoamers throw sediment, thin out at the top or cake in the drum. Some plants read that as spoilage and dump full barrels. Others use it anyway, then watch defoaming fail on the line, lose control of the foam and stop production to clean the tank.
Three questions come up every time this happens, and each one has a practical answer.
- Whether separation actually means the batch has spoiled
- How a separated batch can still be brought back into service
- How to keep defoamers stable through a hot summer
Phase Separation Is Not Spoilage: Why a Defoamer Settles on Standing
Start with the basic fact. When most defoamers sit still for a long time, separating is normal physical behaviour, not a sign the product has gone off.
Every defoamer, oil-based, silicone-based or polyether-based, is a blend of active ingredients, carrier and emulsifier, and those components differ in density. Leave the drum alone and the heavier material drifts to the bottom while the lighter fraction rises. What you see at the top of the drum is simply that split.
Real deterioration looks different. Watch for these signs.
- Flocs or lumps that stay lumpy no matter how long you stir
- A rancid or mouldy smell
- Free oil sitting on top after the emulsion has broken, and no amount of hard stirring brings it back
If all you have is clear liquid on top and sediment below, and the drum goes uniform again after you shake or stir it, the product is still usable.
Bringing a Separated Defoamer Back into Service: Three Steps
Most operators reach for the drum and shake it hard. That is not wrong, but it wastes effort and rarely does the job.
Work through it in three steps.
Step 1 - Invert the container, then roll it
Defoamers ship in everything from 20 kg plastic drums to 1000 kg IBC totes. Where you can manage it, invert a sealed drum and leave it for 2-3 hours, then lay it on its side and roll it for 5-10 minutes. That frees the sediment off the bottom so it can mix back in.
Step 2 - Stir mechanically once the drum is open
Once the drum has been inverted and rolled, open it and work a hand-held or pneumatic agitator through the full depth, bottom to top. The right speed depends on the grade, so check the datasheet or ask the technical team at the supplier. Stop when colour and viscosity look the same from top to bottom.
Step 3 - Sample to check dispersion
Draw a sample from the upper half and another from the lower half. Drop each into a clean beaker of water and watch how it disperses. Both should spread quickly into a uniform milky liquid. If the top sample runs thin and the bottom one comes out thick or pasty, keep stirring.
If the line allows it, dose both samples at the same rate into a foaming test system and compare defoaming speed with a high-speed stirrer or a shake-flask test.
- No real difference in defoaming rate: the batch is blended and ready to dose.
- One sample takes more than 30 % longer to break the foam: the actives are still unevenly distributed, so keep stirring.
One mistake is easy to miss. Never pull only the clear liquid off the top, and never scoop only the sediment off the bottom. The actives will be unevenly spread, your dose will be wrong, and you will either lose foam control or pour money away on an overdose.
Four Steps for Storing Defoamers Through High Summer Temperatures
You can always recover a separated batch, but doing it every week costs time. Good summer storage keeps the split from happening in the first place.
Step 1 - Keep storage temperature below 25 °C
Heat speeds up molecular motion and weakens the way the emulsifier wraps the oil droplets, which is exactly what pushes a batch into separation and free oil. Keep drums in a cool, ventilated warehouse and out of direct sun.
Step 2 - Rotate the stock every few weeks
Standing upright and untouched is what drives sediment to the bottom. If a drum will not be used within a month, invert or roll it every 15-20 days to keep the actives evenly dispersed.
Step 3 - Use an opened drum quickly
Once a drum is open to the air, water evaporates, the product oxidises and microbes can get in. Re-close it properly after every draw. If your line runs slowly, buy smaller packs.
Step 4 - Never blend batches or grades
It is tempting to top up a half-drum with whatever is left in another one. Do not. Emulsifier and stabiliser packages differ slightly from batch to batch, and blending them can break the stable system and bring separation or demulsification on faster. If you have no choice, run a small compatibility test first.
Handling and storage only go so far. The more durable fix is to buy defoamers whose formulation is inherently stable, so the risk of separation never builds up.
Storage stability is one of the core targets in defoamer formulation, and every batch is put through stability testing before it leaves the plant.
If summer separation, sediment or caking keeps disrupting your storage, or a product that used to work has started failing on the line, ask for a sample and the technical data behind it. Storage recommendations and consumption plans can be built around your actual conditions and usage rate.
