Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

403L Silicone-Free Defoamer for Engineered Stone

A silicone-free fatty-alcohol-ether emulsion built for engineered stone (artificial marble) production. It clears surface foam quickly and pulls micro-bubbles off fibres and suspended solids.

Models: 403LForm: Silicone-free emulsionType: Silicone-Free

Overview

403L is a silicone-free high-carbon alcohol ether emulsion defoamer for the foam that engineered stone (artificial marble) production throws up. It clears surface foam quickly and pulls micro-bubbles off fibres and suspended solids. It works at low dose, breaks foam fast and keeps inhibiting.

Key advantages

Silicone-free
Controls foam in engineered stone production
Pulls bubbles off fibres and suspended solids
Low dose, fast break
Inhibition that lasts

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property403L
AppearanceWhite emulsion
Active content40.0±1.0
Viscosity (25 °C, mPa·s)500-2500
pH5.0-7.0
Ionic typeNon-ionic

Recommended applications

  • Engineered stone (artificial marble)
  • Quartz surface manufacture
  • Solid-surface panels
  • Processes that rule out silicone

What decides the model

The decision is about what the product must not contain. Where a silicone residue would break adhesion, printing or coating, the silicone-free routes are the only ones that qualify, and within them the dose and the time the grade holds the foam are what you compare.

This family is published as a single model, so there is no internal comparison to make: the table above is the whole of the data we release on it.

How to trial these models

Silicone-free grades work by defoaming rather than by wetting, which makes them slower to act and longer to hold. Trial them where the coating, the laminate or the printing surface cannot tolerate a silicone residue at all: run the same stepped dose on two split batches, and check the finished surface for pinholes and adhesion loss, not only for foam. The ten-minute foam height matters more than the one-minute figure with this chemistry.

Questions buyers ask about 403L

What is the difference between the 403L models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 403L do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a silicone-free emulsion defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 403L?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 403L shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

200 kg plastic drums of 403l silicone-free defoamer for engineered stone on the loading dock

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Silicone-Free Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.