Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

663-10A Silicone-Free Fatty Alcohol Ether Emulsion Defoamer

A fatty-alcohol-ether emulsion for the many processes that rule silicone out. It breaks foam fast, disperses well, stores stably and degasses cleanly.

Models: 663-10AForm: Silicone-free emulsionType: Silicone-Free

Overview

A high-carbon alcohol ether emulsion defoamer, completely free of silicone, made for the many industries that do not permit silicone — pulp making, black liquor washing and landfill leachate above all. It breaks foam fast and disperses well, stores stably and degasses cleanly. Those four points matter most where foam is stubborn and silicone is off the table.

Key advantages

Silicone-free
Breaks foam fast
Disperses well
Stable in storage
Degasses cleanly

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property663-10A
AppearanceWhite emulsion
Active content35.0±1.0
Viscosity (25 °C, mPa·s)200-1500
pH5.5-7.5
Ionic typeNon-ionic

Recommended applications

What decides the model

The decision is about what the product must not contain. Where a silicone residue would break adhesion, printing or coating, the silicone-free routes are the only ones that qualify, and within them the dose and the time the grade holds the foam are what you compare.

This family is published as a single model, so there is no internal comparison to make: the table above is the whole of the data we release on it.

How to trial these models

Silicone-free grades work by defoaming rather than by wetting, which makes them slower to act and longer to hold. Trial them where the coating, the laminate or the printing surface cannot tolerate a silicone residue at all: run the same stepped dose on two split batches, and check the finished surface for pinholes and adhesion loss, not only for foam. The ten-minute foam height matters more than the one-minute figure with this chemistry.

Questions buyers ask about 663-10A

What is the difference between the 663-10A models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 663-10A do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a silicone-free emulsion defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 663-10A?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 663-10A shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

200 kg plastic drums of 663-10a silicone-free fatty alcohol ether emulsion defoamer on the loading dock

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Silicone-Free Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.