Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

Capped Polyether and Polyether Defoamer Base

Block and random copolymers built from propylene glycol, glycerol or other starters with propylene oxide and ethylene oxide. Non-toxic, efficient, leaves no spotting and picks up little moisture.

Models: Capped PolyetherPolyether Defoamer BaseForm: PolyetherType: Raw Materials

Overview

These polyether defoamers come from block or random polymerisation of propylene glycol, glycerol or other starters with propylene oxide and ethylene oxide. They are non-toxic and efficient, leave no spotting and pick up little moisture, and they stay chemically stable. That makes them a fit for most processes where silicone defoamers are ruled out. They also serve as emulsifiers, in emulsion polymerisation and in detergent formulations.

Key advantages

Non-toxic
Efficient at low dose
No spotting
Picks up little moisture
Chemically stable
Works as an emulsifier or surfactant

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

PropertyCapped PolyetherPolyether Defoamer Base
AppearanceTransparent or pale yellow oily liquidTransparent or pale yellow oily liquid
Viscosity (25 °C, mPa·s)100-900100-900
Ionic typeNon-ionicNon-ionic

Recommended applications

What decides the model

Active content, molecular weight and the ratio inside the material decide what you can build from it. Two materials with the same name can differ in the ratio that governs how the finished emulsion behaves, so the table columns are the specification you formulate against.

The models in this family differ in the properties tabulated above; those columns, rather than a product name, are what a shortlist has to be built on.

How to trial these models

These are base chemistries for formulators rather than finished defoamers, so the trial is a formulation trial. Run it against the concentrate you intend to build: check how the material disperses, whether the emulsion stays stable over the shelf life you need, and whether the active content you calculate from the table matches what the finished batch delivers. Keep a small sample of the reference concentrate so the comparison is like for like.

Questions buyers ask about Capped Polyether

What is the difference between the Capped Polyether / Polyether Defoamer Base models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much Capped Polyether do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a defoamer raw material can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of Capped Polyether?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a Capped Polyether shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

1000 kg IBC tote of capped polyether and polyether defoamer base staged for dispatch

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Raw Materials Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.