Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

Fumed Silica and Tributyl Phosphate

Highly dispersed transparent silica with a large specific surface area and pore volume, plus tributyl phosphate as a defoamer synergist. Supplied as V15, V200 and V380.

Models: Fumed Silica #2V15V200V380Form: Powder and liquidType: Raw Materials

Overview

These fumed silica grades are a highly dispersed transparent powder with a large specific surface area and pore volume, which gives them a high adsorption capacity for solvents and oils. Tributyl phosphate ships alongside as a defoamer synergist.

Key advantages

High specific surface area and pore volume
Adsorbs solvents and oils strongly
Several grades for different rheology targets
Standard reinforcing filler for silicone rubber

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

PropertyFumed Silica #2V15V200V380
pH (4% dispersion)3.6-4.43.8-4.33.6-4.53.6-4.5
Appearance (TBP)Colourless transparent liquidColourless transparent liquidColourless transparent liquidColourless transparent liquid
Density (TBP, g/cm³)0.850-0.9800.850-0.9800.850-0.9800.850-0.980
Solubility (TBP)Soluble in many solvents, insoluble in waterSoluble in many solvents, insoluble in waterSoluble in many solvents, insoluble in waterSoluble in many solvents, insoluble in water

Recommended applications

What decides the model

Active content, molecular weight and the ratio inside the material decide what you can build from it. Two materials with the same name can differ in the ratio that governs how the finished emulsion behaves, so the table columns are the specification you formulate against.

The models in this family differ in the properties tabulated above; those columns, rather than a product name, are what a shortlist has to be built on.

How to trial these models

These are base chemistries for formulators rather than finished defoamers, so the trial is a formulation trial. Run it against the concentrate you intend to build: check how the material disperses, whether the emulsion stays stable over the shelf life you need, and whether the active content you calculate from the table matches what the finished batch delivers. Keep a small sample of the reference concentrate so the comparison is like for like.

Questions buyers ask about Fumed Silica #2

What is the difference between the Fumed Silica #2 / V15 / V200 / V380 models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much Fumed Silica #2 do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a defoamer raw material can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of Fumed Silica #2?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a Fumed Silica #2 shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

25 kg cartons of fumed silica and tributyl phosphate shrink-wrapped on a pallet

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Raw Materials Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.