Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

202 / 7501 Long-Lasting Defoamer for Coatings

The 202 grade pairs polyether ester with mineral oil and hydrophobic silica; 7501 is the waterborne version, built around a dispersing solvent. Neither one leaves surface defects or interferes with film formation.

Models: 2027501Form: Compound concentrateType: Mineral Oil / PE Ester

Overview

The 202 grade is a polyether ester with mineral oil and hydrophobic silica; 7501 is the waterborne version, where a dispersing solvent takes the place of the mineral oil. Both fit any aqueous system. Foam breaks fast and stays down, and neither leaves surface defects nor interferes with film formation.

Key advantages

Fits any aqueous system
Breaks foam fast
Holds inhibition through the run
No surface defects
Does not interfere with film formation

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property2027501
AppearancePale yellow cloudy viscous liquidYellow oily liquid
Active content≥95.0≥95.0
Viscosity (25 °C, mPa·s)200-1500200-1500
Ionic typeNon-ionicNon-ionic

Recommended applications

What decides the model

Carrier oil, active content and cost per kilo of active matter decide this range. The ester and polyether-ester grades are chosen where a straight mineral oil would affect the finished film or sheet; the mineral-oil grades are chosen where nothing downstream is sensitive to oil.

The models in this family differ in the properties tabulated above; those columns, rather than a product name, are what a shortlist has to be built on.

How to trial these models

Mineral-oil, ester and polyether-ester grades are the economical route for aqueous systems that do not need silicone performance. They carry a carrier oil, so trial them on the same batch you will run commercially and check for any effect on the downstream film, print or sheet: oil-based grades can change drying or appearance where silicone grades would not. Read the ten-minute foam height and the appearance of the finished product together.

Questions buyers ask about 202

What is the difference between the 202 / 7501 models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 202 do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a mineral oil & polyether ester defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 202?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 202 shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

200 kg plastic drums of 202 / 7501 long-lasting defoamer for coatings on the loading dock

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Mineral Oil / PE Ester Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.